15 LACK tables as Metabolight interactive display unit

15 LACK tables hacked as Metabolight interactive display unit

IKEA items used:

15 x Lack tables, white

Other items:

5mm Perspex panels with printed or cut vinyl
8mm white slide binders
MattWhite vinyl
18mm MDF base board
Batten light holders
Double sided tape
Screws
L-brackets
Fixing plates

We were commissioned to make a travelling, portable exhibition as part of a project for University College London Engineering. While looking for possible solutions we happened upon the Lack table, the perfect white box for only £5! We bought a few and played around with them, stacking them up and filling the openings with images and information.

After a few tests we found a way to build them into simple towers with perspex panels filling the apertures between the legs, while still being able to disassemble and flat pack them with relative ease. The stand is made up of 5 different towers of Lack tables fixed to two base board for stability.

15 LACK tables hacked as Metabolight interactive display unit

The towers are built from the top down with the top most table being a basic Lack table. The second table top is then screwed into the bottom of the legs before having its own legs attached with the standard IKEA double sided screws. The process is then repeated until the desired height is reached. Simple!

Slide binders are affixed to the inside of the legs with double sided tape to hold perspex panels. The panels can then be slid in easily. The panels for each table need to be added as the towers are built to ensure they were held tightly.

Holes were drilled into some of the table tops so that light bulbs could be threaded through and illuminate the perspex panels from behind.

15 LACK tables hacked as Metabolight interactive display unit

Once the separate towers are assembled, they are arranged on the base boards and L-brackets are used to fix them in place. A few fixing plates are also used to tie the towers together and give them a bit of extra rigidity.

Then it’s all done! The perfect platform for information panels and interactive displays.

~ by Michael, Design Science

More ways to use the LACK as a display stand

The “Lack Freischwinger” is a compact, easy to build table suitable for exhibitions or displaying of artifacts. Read more.

LACK side tables glued onto 45 x 45 mm planks and wall mounted as a product display panel. Read more.

Great find from Source Ikeahacker

Comments

Mind the gap: Fit IKEA MALM over a tall baseboard

I forgot one thing when I ordered the MALM dresser : The baseboards in my apartment are very tall and very wide. So, when I installed it, I had a 4 cm gap between the wall and the back of the cabinet which was not aesthetically possible for me. As it is not possible to cut the back of dresser at the bottom to leave room for the tall baseboard, I decided that MALM should be raised. And it was much simpler than I had imagined. You’ll need: A MALM dresser (mine is a 6-drawer chest) Six oak bed legs (I think five would have been enough, but while I was there …) 6 mounting plates A piece of plywood the size of the bottom of the cabinet (I went to the hardware store next door, it cost me less than 5€) Screws White adhesive edging tape How to raise the MALM dresser above a tall baseboard Place the MALM upside down. Fix the plywood onto the underside of the MALM with screws. Predrill holes for the leg screws (if you have the same baseboard problem as me, make sure you measur...

IKEA KALLAX Queen Storage Bed

I built this prior to knowing this website existed, this probably would have saved some contemplation. For difficulty reference, I am no carpenter (electrician actually) and I built it with my right hand in a cast. We bought an old house with original hardwood flooring from the 40s so we were very concerned about damaging it. The casters on a normal bed frame put a lot of pressure on a small surface and we didn’t want it dented or damaged if things started a rockin …. Plus, a 40′s house has virtually no storage as you only needed 3 pairs of pants back then. IKEA material : 3 x KALLAX shelf units (4) 4 x KALLAX drawer kits 8 x KALLAX fabric boxes Non-IKEA material : 4 x 2×4 A grade (saves time) 2 x 2×6 2 x sheets 1/2″ plywood (what ever grade you want) 25ft x iron-on edge trim 100 x 3″ #8 wood screws 20 x 1-1/4″ #8 wood screws satin white paint Tools (I used) : Tape measure Drill w/ 1/8″ bit for piloting holes Impact driver for screws Table saw Miter saw Ass...

How to Document the Home Building Process

Building your home is a unique experience filled with stories you will never forget. There is also important information you need to remember if you build, even after you settle in. Whether it’s for your family or for future renovations, documenting your build is an important part of the process. Keeping track of your documents and making sure your family stay in the loop can help you stay organized and make sure you remember everything about your build. Not sure how to stay on top of all of the details? Document the process with these simple tips so you can always look back on it fondly. Collect this idea Use social media and involve your friends. Image: Kroiss Development Keep friends and family in the loop The home building process is exciting and your friends and family will want to be included. In fact, you’ll probably find that your new home becomes a popular conversation topic. You don’t need to personally keep everyone in the loop. Instead, you can find ways to keep ev...

Joyce Ford Blog

Search This Blog