Skip to main content

The Beautiful Big Table: A perfect dual workstation

My wife and I wanted a large single table for our studio. She works on one side and I do on the other. Tables this large are fewer in selection and cost around $1K+ for one that is decently designed and built, but we didn’t like anything that we found. We built this for $665 and it took one person an hour to put it together.

The Beautiful Big Table: A perfect dual workstation

IKEA items used: (2) Karlby countertop, walnut. L98×25⅝x1½”

We used two IKEA Karlby countertops. They are made primarily from particle board, but IKEA chose to use extra thick 1/8″ walnut veneer laminated on top. Its been finished in a hard wax oil so it’s designed to be refinished and last. The countertops come with a 25 year limited warranty as an indication of how long they’re intended to last when installed as intended in kitchens.

The Beautiful Big Table: A perfect dual workstation

We clamped the countertops together with 4 panel clamps. This makes a strong and stable center seam so the halves both reinforce one another and remain aligned. We then bolted the joined top on two sawhorse legs from McMaster-Carr Supply. Each sawhorse was mounted on the lengthwise center of the top and 24″ from each of its ends. The sawhorses are mounted perpendicular to the center seam with their midpoints aligned to the seam.

The Beautiful Big Table: A perfect dual workstation

We used bolts to fasten the panel clamps and legs to the top. Since the top is constructed from particle board, we installed metal threaded inserts into the countertops with epoxy.

The Beautiful Big Table: A perfect dual workstation

I had wondered if the top would require additional center reinforcement to prevent lengthwise bowing over time, but decided to wait and see. Its been used for two years now with heavy computer monitors sitting dead center and I can only see very minimal bowing when I sight the top from one corner along the lengthwise edge.

I recently got around to finishing the cable routing. I used a nickel plated brass grommet from Mockett and F6 woven wrap from Wirecare to route most of our electrical cords. The textile cover wraps onto itself making it relatively easing to fold cords into and out of it as you need.

The Beautiful Big Table: A perfect dual workstation

I’m was so happy with how the table had turned out that it was worth refinishing it. I thoroughly sanded the top surface and edges to 120 grit and followed by 180 grit to get past the hard wax oil. It wasn’t hard. I wiped off the dust with damp paper towels, let it dry, and then flooded the surface with Danish oil using a cheap china bristle disposable brush. I let it set 15 minutes and then applied more oil over the entire surface. After waiting another 30 minutes, I wiped it with clean cotton rags. The next day, I sanded to 220 grit, wiped off the dust, and repeated the oiling technique. The day after, I sanded to 320 grit, cleaned off the dust, and applied the final coat of oil using the same technique again. It greatly enriched the depth and saturation of color in the walnut in addition to providing a satisfying smooth surface to lay your hands on.

The Beautiful Big Table: A perfect dual workstation

Here’s our full materials and costs list for our big table:

Essential

- 2 x Adjustable height sawhorse from McMaster-Carr (8055T31), $63.08 each = $126.16
- 2 x Karlby countertop, walnut. L98×25⅝x1½” from IKEA (Article Number: 703.352.12), $219 each = $438.00
- 4 x Double Acting Joint Fastener from Amazon, $14.65 each = $58.60
- 1 x 1/4-20-Inch x 1-Inch Full Thread Hex Tap Bolts, 100-Piece, Amazon, $9.84 each = $9.84
- 1 x E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 1/4″-20 Internal Threads, 25mm Length (Pack of 50), Amazon, $7.50 each = $7.50
- 1 x E-Z Lok Threaded Insert, Zinc, Hex-Flanged, 3/8″-16 Internal Threads, 25mm Length (Pack of 25), Amazon, $6.00 = $6.00
- 1 x 3/8-16-Inch x 1-Inch Course Hex Bolts, 100-Piece, Amazon, $18.84 each = $18.84

Total = $664.94

Extras

- Epoxy, bonds metal and wood. Use on threaded inserts
- Danish oil, natural
- 120 grit sandpaper
- 180 grit sandpaper
- 220 grit sandpaper
- 320 grit sandpaper
- Cheap brush, China bristle white
- Clean cotton rags
- 1 x F6 Woven Wrap for cord covers, Wirecare (F6W0.50WH), $35.10 each = $35.10
- 1 x F6 Woven Wrap for cord covers, Wirecare (F6W0.75WH), $15.95 each = $15.95
- 1 x Metal Grommet 2-1/2″ solid brass, Mockett (MM6A-17S), $12.85 each = $12.85
- Hole saw to match grommet diameter

~ by Mark Bechtel and Ruchika Modi

Great find from Source Ikeahacker

Comments

Post a Comment

Popular posts from this blog

Mind the gap: Fit IKEA MALM over a tall baseboard

I forgot one thing when I ordered the MALM dresser : The baseboards in my apartment are very tall and very wide. So, when I installed it, I had a 4 cm gap between the wall and the back of the cabinet which was not aesthetically possible for me. As it is not possible to cut the back of dresser at the bottom to leave room for the tall baseboard, I decided that MALM should be raised. And it was much simpler than I had imagined. You’ll need: A MALM dresser (mine is a 6-drawer chest) Six oak bed legs (I think five would have been enough, but while I was there …) 6 mounting plates A piece of plywood the size of the bottom of the cabinet (I went to the hardware store next door, it cost me less than 5€) Screws White adhesive edging tape How to raise the MALM dresser above a tall baseboard Place the MALM upside down. Fix the plywood onto the underside of the MALM with screws. Predrill holes for the leg screws (if you have the same baseboard problem as me, make sure you measur...
Post a Comment
Read more

How to Document the Home Building Process

Building your home is a unique experience filled with stories you will never forget. There is also important information you need to remember if you build, even after you settle in. Whether it’s for your family or for future renovations, documenting your build is an important part of the process. Keeping track of your documents and making sure your family stay in the loop can help you stay organized and make sure you remember everything about your build. Not sure how to stay on top of all of the details? Document the process with these simple tips so you can always look back on it fondly. Collect this idea Use social media and involve your friends. Image: Kroiss Development Keep friends and family in the loop The home building process is exciting and your friends and family will want to be included. In fact, you’ll probably find that your new home becomes a popular conversation topic. You don’t need to personally keep everyone in the loop. Instead, you can find ways to keep ev...
1 comment
Read more

IKEA KALLAX Queen Storage Bed

I built this prior to knowing this website existed, this probably would have saved some contemplation. For difficulty reference, I am no carpenter (electrician actually) and I built it with my right hand in a cast. We bought an old house with original hardwood flooring from the 40s so we were very concerned about damaging it. The casters on a normal bed frame put a lot of pressure on a small surface and we didn’t want it dented or damaged if things started a rockin …. Plus, a 40′s house has virtually no storage as you only needed 3 pairs of pants back then. IKEA material : 3 x KALLAX shelf units (4) 4 x KALLAX drawer kits 8 x KALLAX fabric boxes Non-IKEA material : 4 x 2×4 A grade (saves time) 2 x 2×6 2 x sheets 1/2″ plywood (what ever grade you want) 25ft x iron-on edge trim 100 x 3″ #8 wood screws 20 x 1-1/4″ #8 wood screws satin white paint Tools (I used) : Tape measure Drill w/ 1/8″ bit for piloting holes Impact driver for screws Table saw Miter saw Ass...
Post a Comment
Read more