Skip to main content

Workshop Tool Bench from BEKVAM Kitchen Trolley

Having built a small garden workshop I needed a tool bench for my stationary tools such as a band saw and drill-press. An earlier project had resulted in a simple mobile stand for the band-saw from off-cuts of plywood and MDF. However the drill-press was much heavier at around 25Kg so a more substantial tool stand was required. But crucially it still needed to be mobile.

The BEKVÄM Kitchen trolley was the obvious starting point. It has two fixed castors and two legs making it both sturdy and mobile. It’s made from solid beech so will easily support the tool’s weight. And perhaps more importantly, it’s really inexpensive being just 35 GBP in the UK. To put that in perspective, the same quantity of beech from a timber yard would have cost at least 10 GBP more.

Materials

  • BEKVÄM Kitchen Trolley (302.403.48)
  • 18mm (3/4”) MDF (375mm x 520mm) (x 2)
  • 9mm x 32mm Pine Stripwood (1.4m approx.)
  • 9mm x 100mm OSB board (390mm length approx.)
  • 3.5mm x 16mm woodscrews ( x 10)
  • Wood glue
  • SKYDD Wood Treatment Oil (Mineral Oil) 500ml

Workshop Tool Bench Video Tutorial

Comments

Popular posts from this blog

Mind the gap: Fit IKEA MALM over a tall baseboard

I forgot one thing when I ordered the MALM dresser : The baseboards in my apartment are very tall and very wide. So, when I installed it, I had a 4 cm gap between the wall and the back of the cabinet which was not aesthetically possible for me. As it is not possible to cut the back of dresser at the bottom to leave room for the tall baseboard, I decided that MALM should be raised. And it was much simpler than I had imagined. You’ll need: A MALM dresser (mine is a 6-drawer chest) Six oak bed legs (I think five would have been enough, but while I was there …) 6 mounting plates A piece of plywood the size of the bottom of the cabinet (I went to the hardware store next door, it cost me less than 5€) Screws White adhesive edging tape How to raise the MALM dresser above a tall baseboard Place the MALM upside down. Fix the plywood onto the underside of the MALM with screws. Predrill holes for the leg screws (if you have the same baseboard problem as me, make sure you measur...

How to Document the Home Building Process

Building your home is a unique experience filled with stories you will never forget. There is also important information you need to remember if you build, even after you settle in. Whether it’s for your family or for future renovations, documenting your build is an important part of the process. Keeping track of your documents and making sure your family stay in the loop can help you stay organized and make sure you remember everything about your build. Not sure how to stay on top of all of the details? Document the process with these simple tips so you can always look back on it fondly. Collect this idea Use social media and involve your friends. Image: Kroiss Development Keep friends and family in the loop The home building process is exciting and your friends and family will want to be included. In fact, you’ll probably find that your new home becomes a popular conversation topic. You don’t need to personally keep everyone in the loop. Instead, you can find ways to keep ev...

Brighten up: A reading lamp the book lover will love

We already had a MAGNARP table lamp in the living room, but we were missing a reading lamp next to our couch. For a standing MAGNARP floor lamp, we didn’t have space. And the available other IKEA lamps were not for our taste. I already saw solutions with FRÄCK , so I decided to make my own wall mounted reading light, fused with MAGNARP. Here goes: IKEA items used: Steps for an IKEA wall mounted reading light: 1. Take apart both sets. 2. Cut the power line of the MAGNARP to be able to pull it out from the pipe. (Cut at both ends of the switch) 3. Cut the pipe. Besides the threaded part which goes inside the bulb socket you I will need approximate 5mm. 4. Cut M10 thread on the pipe’s end, and drill over the thread inside the main plate with M10 as well. 5. Bend the mirror’s fork as seen on the picture. 6. Mark the holes from the bent fork onto the main plate, and drill holes. 7. Make the electric work with a new switch. (I laced it inside the arm before doing so...