Skip to main content

Homemade Healing Salve

Processed with VSCO with a6 preset

Processed with VSCO with a6 preset

Processed with VSCO with a6 preset

Processed with VSCO with a6 preset

I’ve recently been researching the healing benefits of calendula oil, specifically in salves and creams.

“One of the best reasons to keep calendula handy is due to its healing abilities. If you apply this flower oil to your cuts, scrapes, bruises, and insect bites, you can quickly speed the healing process, partially due to the anti-inflammatory properties of the oil, in addition to the unique antioxidant compounds found in this miraculous plant. By protecting against infections, it keeps wounds and scrapes safe, allowing them to heal rapidly.” – Source http://www.organicfacts.net

While I’m thankful that no one in our family suffers from any skin conditions. I think a healing cream is nice to have on hand. I’ve been checking different recipes on Pinterest and decided to base my recipe off of different ones I’ve seen on Pinterest. Thankfully, minus the calendula oil I had all of the ingredients I needed on hand. With a quick trip to my local dry goods store they ordered me some and I had it in my hands in a few days. I also purchased some flowers to make my own, however infusion takes at least a month and I really wanted to make some before then.

Here are the ingredients I used [organic is always preferred]

4 tablespoons almond oil
2 tablespoons calendula oil
4 tablespoons coconut oil
2 tablespoons olive oil
2 tablespoons vitamin e oil
1 tablespoon beeswax [on my next batch I’ll likely use 1 more tablespoon of beeswax to create a creamer consistency. So if you want a creamier consistency use 2 full tablespoons.]
1 tablespoon shea butter
5 drops frankincense
5 drops lavender
5 drops tea tree

[should yield about 8 oz]

I decided to begin with only 8oz of creamy salve, knowing it would likely last some time. As always I suggest educating yourself on the benefits of using essential oils. And be sure to know how to safely use them in your home. Knowledge is power, my friends!

I decided to go with Lavender, Frankincense and Tea Tree oils because they are three of my favorites and because they are all safe to use on or around my children. Lavender is a known pain reducer as well as being able to help heal burns and wounds. Frankincense is a known antiseptic and disinfectant and overall is great for our skin and Tea Tree oil is also a powerful antiseptic. A powerful combination in a healing salve!

Just like other recipes I’ve shared you’ll need to melt your oils [minus essential oils] beeswax and shea butter together in a double boiler. I have specific ones containers and pans that I only use for these homemade recipes. Once everything is happily melted together you’ll need to pour it into your clean jar and add your oils. Give it a little stir, place your lid on top and set aside to cool overnight.

I hope you all enjoy this recipe. I’d love to hear if you have your own recipe or if you decide to make this one!

Blessings,

Bree xx


Great post originally from The Homemaking Momma

Comments

Post a Comment

Popular posts from this blog

Mind the gap: Fit IKEA MALM over a tall baseboard

I forgot one thing when I ordered the MALM dresser : The baseboards in my apartment are very tall and very wide. So, when I installed it, I had a 4 cm gap between the wall and the back of the cabinet which was not aesthetically possible for me. As it is not possible to cut the back of dresser at the bottom to leave room for the tall baseboard, I decided that MALM should be raised. And it was much simpler than I had imagined. You’ll need: A MALM dresser (mine is a 6-drawer chest) Six oak bed legs (I think five would have been enough, but while I was there …) 6 mounting plates A piece of plywood the size of the bottom of the cabinet (I went to the hardware store next door, it cost me less than 5€) Screws White adhesive edging tape How to raise the MALM dresser above a tall baseboard Place the MALM upside down. Fix the plywood onto the underside of the MALM with screws. Predrill holes for the leg screws (if you have the same baseboard problem as me, make sure you measur...
Post a Comment
Read more

How to Document the Home Building Process

Building your home is a unique experience filled with stories you will never forget. There is also important information you need to remember if you build, even after you settle in. Whether it’s for your family or for future renovations, documenting your build is an important part of the process. Keeping track of your documents and making sure your family stay in the loop can help you stay organized and make sure you remember everything about your build. Not sure how to stay on top of all of the details? Document the process with these simple tips so you can always look back on it fondly. Collect this idea Use social media and involve your friends. Image: Kroiss Development Keep friends and family in the loop The home building process is exciting and your friends and family will want to be included. In fact, you’ll probably find that your new home becomes a popular conversation topic. You don’t need to personally keep everyone in the loop. Instead, you can find ways to keep ev...
1 comment
Read more

Brighten up: A reading lamp the book lover will love

We already had a MAGNARP table lamp in the living room, but we were missing a reading lamp next to our couch. For a standing MAGNARP floor lamp, we didn’t have space. And the available other IKEA lamps were not for our taste. I already saw solutions with FRÄCK , so I decided to make my own wall mounted reading light, fused with MAGNARP. Here goes: IKEA items used: Steps for an IKEA wall mounted reading light: 1. Take apart both sets. 2. Cut the power line of the MAGNARP to be able to pull it out from the pipe. (Cut at both ends of the switch) 3. Cut the pipe. Besides the threaded part which goes inside the bulb socket you I will need approximate 5mm. 4. Cut M10 thread on the pipe’s end, and drill over the thread inside the main plate with M10 as well. 5. Bend the mirror’s fork as seen on the picture. 6. Mark the holes from the bent fork onto the main plate, and drill holes. 7. Make the electric work with a new switch. (I laced it inside the arm before doing so...
Post a Comment
Read more